TM 5-3895-356-14&P
37 degrees swivel female fitting on the filter end. A
2. Hydraulic Pump Controls
similar hose arrangement for the line between the filter
Attach cable support bracket to right chassis frame using
discharge and pump suction port are to be used
two (2) 1/2 X 1 1/2" bolts as seen in Fig. 44. Holes for
Connect one end of the 3/4" gray return hose to
this bracket were made available when brackets for tool
return port in the reservoir (Fig. 45) and lay hose along
box were removed.
inside of right hand chassis frame channel.
Next feed micro control cable up through 7/8" hole in cab
floor to control mounting bracket. Slip rubber grommet
over upper end of cable Thread jam nut onto upper end,
K. Frame Extension Assembly
push cable through control bracket, turn on second ]am
Bolt extension plates to chassis frame (Figure 51) using
nut and secure control cable to control bracket, turn on
four (4) 1/2 X 1 1/2" bolts. The extension plate holes will
second jam nut and secure control cable to control
match with existing holes made available in the frame by
bracket. Refer to Fig. 49 for assembly arrangement.
removal of the rear crossmember Slip frame extension
Next turn lock ring and position tube onto upper end of
channel over extension plate such that the extension
cable. Finally, install cable jam nut and knob. At lower
channel is flush with top of chassis frame. Hold in place
end of cable use two lock nuts to locate and secure
with a "C" clamp and weld extension channel to
attaching stud on control cable so as to align stud with
extension plate. Do this procedure for both sides of
cable support bracket hole (Fig. 49). Attach override
chassis frame WARNING:
DO NOT WELD TO
control assembly to lower end of control cable core. In
CHASSIS FRAME.
turn connect override assembly to control linkage and
finally to upper most hole in pivot lever assembly. Then
II.
MOUNTING OF DISTRIBUTOR ON TRUCK
install front override control cable and attach to lowest
CHASSIS
hole in pivot lever (Fig. 49). Connect pump control
linkage to first hole below center hole in pivot lever with
A. Placement of Distributor
pump control lever Finally attach rear override cable to
Remove distributor from skid Remove fenders and rear
upper most hole in pivot lever, and place along inside of
support blocks from the distributor in preparation for
right hand chassis frame (Fig. 48). Again secure cable
placement of distributor onto chassis.
in place with self-locking ties
Check to insure distributor frame blocks are taped to leg
support channels as seen in Fig. 52. Slip distributor
3. Electrical Switches and Controls
onto chassis (Fig. 52) being careful not to damage vacu-
Mount cab control switches to dash using (2)
flo tubes with under side of frame members. Note
number 14 X 1" drill screws (Fig. 61).
clearance between vacu-flo tubes and underside of
chassis frame (Fig. 50) is normal for standard mounting
J. Hydraulic Hose Attachment
procedure. Locate distributor such that lifting eye on rear
bogie assembly (located midway between rear axles)
1. High Pressure Hose Attachment
aligns with cable guard channel on side of distributor
While the distributor is still skid mounted, remove
(Fig. 53). Also at this time see Fig. 1 for a completed
the rear bar carrier box and attach the 3/4" high pressure
distributor installation. When this is accomplished slide
hoses to the hydraulic motor (Figure 50). Thread the
rear support blocks between chassis, and distributor
right hand hose forward between asphalt pump and
frame Locate rear support blocks(Fig.
53) Lower
distributor frame extensions and lay m carriers provided
distributor front leg support channels onto chassis frame.
on cross stringers between tank legs. Repeat a similar
Using four (4) 1/2 X 22 tie down bolts, frame clips
procedure for the left hand hose. Care should be taken
and mounting springs, secure both left and right front
to keep hoses clear of rotating or moving distributor
distributor channel supports to chassis frame (Fig. 54).
components Also, leave dust covers on pump end of
Weld frame clips to top of leg support channel for both
hoses.
sides Next using four (4) 1/2 X 18" tie down bolts and
frame clips, secure the distributor to chassis frame at
second distributor support and half way between the
2. Suction and Return Hose
Connect 3/4" suction hose from reservoir tee to inlet
will be on the reservoir end and
33
